2mm e-coated sheet steel, blue RAL 5015, hatch equipped with a Ronis 405 lock.
2mm sheet steel treated with phosphate coating and white RAL 9010.
Polyester powder coating cured at 250°C, housing RAL 5015, top cover RAL 9010.
Boom from 2 to 6m in length:
Oval anodised aluminium 84 x 57mm ≤ 6m, reflective bands.
Counterbalance compression spring.
Manually operated by 10 turns of the handle with an anti-restart safety lock.
Three-phase 0.18KW geared unit powered by a variable frequency drive with a 230V single-phase power supply. Double-wheel worm gear speed reducer, greased for life with a 17mm shaft crank.
Barrier with geared motor, counterbalance and boom support. Isolation switch, variable frequency drive, programmable PLC. Inductive, non-contact proximity sensors for adjusting the boom. Anti-condensation heating 230V 32W. Hand crank for emergency manual operation (with limit switch safety device). Set of keys for the maintenance hatch. Instructions for installation, connection, commissioning and maintenance. Oval anodised aluminium boom 84 x 57mm with reflective bands.
PVC anchor plate + 4 Ø 16 x 250mm shanks + 8 bolts. Anchor plate for rotating barrier + 4 Ø 16 x 250mm shanks + stainless steel disk. Fixed tubular support post 60 x 60 x 1200mm. Support post with height adjustable from 800 to 1200mm, fixed with 4 anchor pins. Fixed support post with 230kg magnetic pull. Pendulum support post adjustable from 800 to 1000mm. GTH-type lower folding skirt or both upper and lower folding skirts. Boom locking through the internal system in the housing. Folding boom with ≤ 3.80m arm, with a height of ≤ 2.50m under a ceiling. Custom polyester paint colour available (RAL to be defined). Warning signs (ø320mm standard): STOP or WRONG DIRECTION. Motion detector on a magnetic loop, infra-red sensor, ultrasonic detector. Local control devices: emergency services access cabinet, push-button, etc. Cardin radio receiver, 433 MHz 1 to 4 channels, European standard. Access controls: card readers, keypads, etc. Automatic raising if no U-bar < 6m. Unhinging device for use on highways. Solar power possible, please contact us.
Delivers a signal through a 3A / 250V dry contact when a token is put in the slot (e.g.: to open the barrier).
Barrier with licence plate reader
An all-in-one solution with a licence plate reader integrated directly into the barrier housing. This system allows for the efficient management of the access control and identification of those passing through the barrier. Applications: paid car parks, hotel/camp site entrances, company car parks, etc.... Cameras may be installed on the right or left.
Button box – 1 push-button for opening/ 1 push-button for closing Control console: composed of 2 push-buttons for opening and closing. Button box – 1 push-button for opening / 1 automatic/press switch. Control console composed of: - 1 button for opening/closing – Automatic closing, - 1 automatic switch – Holds open.
Emergency services box
Emergency services box in red cast aluminium with triangle lock 3 possible opening options: - 405 key (access to the barrier or manually opened gate). - Integrated limit switch to automatically open the barrier or gate. - Switch to automatically open the gate or barrier. Dimensions: 170 w x 140 h x 48 d.
Power supply: 12 / 24 VAC – DC. Range: - 15ml for a CDR 842 A type receiver - 60ml for a CDR 852 A type receiver Operating temperatures: - 10 °C + 55 °C Paint: High resistance. Emitter and receiver: in waterproof aluminium cases. Optical head: Mounted on a moveable self-locking pivot, adjustable horizontally through a rotation of 180° and vertically through a rotation of +/- 30° from its normal starting position. Dual control: Double relays with changeover contact in series.
Keypad: 12 metal keys - backlit with blue LED lights. Case: Stainless steel front. Weight: 700g. Dimensions: 78/73 w x 125/119 h x 54/47 d mm. Power supply: 12 to 24 V AC/DC. Average power consumption: 50 amps. Operating temperatures: - 20 °C to + 70 °C. IP: 66. Relay outputs: 2 changeover contacts (NO/NF) Relays 1 = 30V DC/5A Relays 2 = 30V DC/1A
Totaliser without pre-selection - LCD 24 x 48 - non-backlit model - Display: 8 digit LCD, 8mm height - Lithium battery power supply, - Counter input: static (4-30 VDC) or voltage (10 → 260 VAC), - Reset from unit or externally with inhibition option, - Cutting accessories 50 x 25mm.
Magnetic loop sensor
Double or single channel sensor with microprocessor. Dimensions: Height 78mm, width 41mm, depth 78mm.
Range: 350 to 3,400mm. Casing: cylindrical M30. Main body: nickel-plated brass, some parts in PBT and TPU plastic. Supply voltage: 9-30 V CC, protected against polarity reversals. No-load current consumption: = ≤80 mA. Output: 1 pnp switch output. Imax = 200 Ma.
Oval boom with LEDs
Additional flat positioning light with LEDs for oval boom. Dimensions: 65 x 16 x 15mm, spaced at 45mm apart.
24V flashing light
Operating voltage: 24 DC - Polystyrene base, - Polycarbonate cover, - Long-life xenon flash tubes, - Highly reliable, xenon flash tubes last for over 3,000 hours, - Entirely inert, resistant to impacts and vibration, - Protected against changes in polarity and interference, - Base and cover sealed together to ensure better water tightness. Dimensions: 77 w x 45 h.
230V flashing light
Operating voltage: 230V - Polystyrene base, - Polycarbonate cover, - Long-life xenon flash tubes, - Highly reliable, xenon flash tubes last for over 3,000 hours, - Entirely inert, resistant to impacts and vibration, - Protected against changes in polarity and interference, - Base and cover sealed together to ensure better water tightness.
Orange light Ø140-180
FH LED light Ø180mm.
R23 light Ø 120mm. Dimensions: (H x W x D): 410 x 180 x 290mm.
R24 light Ø 200mm. Dimensions: (H x W x D): 399 x 251 x 441mm.
Passage indication light (red-green)
High visibility red/green LED lights integrated into the top cover. Designed for: - Indicating to vehicles that they may pass, - Increases visibility in poorly lit areas: car parks, residential sites, industrial sites, logistics sites, etc...., - Suitable for indoor (e.g.: covered parking area) or outdoor (site entrance, outdoor parking) usage.
Programming: Daily programming clock.
One-way intercom 1 door station + 1 internal phone. Audio intercom kit with 2 wires, composed of a single-button door station, an internal post and a 230VAC/12VAC power supply.
The tropicalisation kit includes: - 2 ventilators with filters, - 1 fan, - 1 heater. This kit is adapted for use in both hot and humid environments.
PROXIMITY Compact is an access control system for doors. All the electrical components of the system are integrated into the reader casing. Compact systems can be installed on several doors at the same site, using the same badges. Readers from the P range are supplied with a choice of black or white panels which can be added after installation is complete.
Pedestrian warning sign
Sign made from A13b-type PVC. Overall dimensions: 29cm x 33cm in height. Fixed using a plastic or stainless steel collar.
Spaces/Full sign - High luminosity LEDs, - Black grained ABS panel, - "SPACES" in green LEDs, - "FULL" text in red LEDs, - 230 VAC power supply, - HO7RNF 3 × 1mm power supply cable.
Front unhinging support for oval boom
Boom support with front unhinging system (compatible with straight or folding boom). Nylon screw to indicate unhinging. Optional: Boom unhinging detection system with information report. LBA6/63 barrier types.
Boom release support
Boom support with front release system (compatible with straight or folding boom). Allows the boom to be released in the event of an impact. Boom is fixed to the support with 4 nylon M8 x 25 screws.
La Barrière Automatique offers different varieties of terminals and access posts that can be integrated into any kind of access control: badge readers, sensors, intercoms, lights, etc. VL/PL posts. Sensor support post. Ø 80mm / 50mm signal light support post. Galvanised steel post.
S449 Radio receiver/transmitter
80 x 80 x 1200 support with 250kg magnet.
- Built-in siren, - Sound level: 90 dB for any application, - Continuous / rising and falling sound, - Models with terminal blocks, protected electronic circuits, - 28mm diameter holes for attaching the siren, - Low power consumption
- Siren, - Sound level: 90 dB for any application, - Continuous / rising and falling sound, - Models with terminal blocks, protected electronic circuits, - 28mm diameter holes for attaching the siren, - Low power consumption
Adjustable 230V siren
85-105 dB – 230V siren - Very powerful piezo buzzer, - Sizes: Ø 65mm, - Select from 3 distinct sounds, - Adjustable sound level, even if the device is already installed, - Ø 30.5mm holes for installation.
230V bell – 105 dB at 1 metre.
Backlit mount for a logo
Aimed at efficiently improving your company's visual communication. Dimensions: 240 x 60mm.
Advertisement mount for boom
Advertisement mount for installation on a straight or folding oval boom. Polystyrene base covered in white plastic film. Support for straight boom: 250 x 150 x 1000mm. Mount for primary folding boom: 350 x 150 x 1000mm.
Locking for the LBA6R-7R-63 boom
Boom locking through the internal system in the housing allows the boom to be locked in position. It replaces the magnet and means that the support for the end of the boom is no longer required. The system is protected from vandalism due to being completely integrated into the barrier. The locking is controlled by the barrier's programmable PLC (no need for any additional control equipment).