3mm e-coated sheet steel, blue RAL 5015, hatch equipped with a Ronis 405 lock.
2mm aluminium sheet phosphate coating, white RAL 9010.
Polyester powder coating cured at 250°C, housing RAL 5015, top cover RAL 9010.
Boom from 3 to 6m in length:
Reinforced aluminium 180 x 118mm, lacquered white + reflective red and white bands.
Galvanised 8mm steel for 180 x 118mm aluminium boom.
Counterbalance compression spring + guide, chain and sprocket (replacing the counterweight).
Manually operated by 11 turns of the handle with an anti-restart safety lock.
Three-phase 0.55KW brake geared unit powered by a variable frequency drive with a single-phase 230V power supply. Double-wheel worm gear speed reducer, greased for life with a 17mm shaft crank.
Barrier with geared motor, counterbalance and half-shell. Isolation switch, variable frequency drive, programmable PLC. Inductive sensors without contacts, for adjusting the boom. Anti-condensation heating 230V 32W. 180 x 118mm Class 1 reinforced aluminium boom. Hand crank for emergency manual operation (with limit switch safety device). Set of keys for the maintenance hatch. Instructions for installation, connection, commissioning and maintenance.
Aluminium housing - lisse 135 x 93 mm - PVC anchor plate + 4 Ø 16 x 250mm shanks + 8 bolts. Anchor plate for rotating barrier + 4 Ø 16x 250mm shanks + stainless steel disk. Automatic rotation system. Fixed tubular support post 80 x 80 x 1200mm. Support post with height adjustable from 800 to 1200mm, fixed with 4 anchor pins. articulated arm (with arm 175x75mm) - Fixed support post with 230kg magnetic pull. Pendulum support post adjustable from 800 to 1000mm. GTH-type lower folding skirt or both upper and lower folding skirts. Boom locking through the internal system in the housing. Custom polyester paint colours available (RAL to be defined). Warning signs: STOP or WRONG DIRECTION. Motion detector on a magnetic loop, infra-red sensor, ultrasonic detector. Local control devices: emergency services access cabinet, push-button, etc. Cardin radio receiver, 433 MHz 1 to 4 channels, European standard. Access controls: card readers, keypads, etc. Automatic raising if no U-bar < 4.50m. Solar power possible, please contact us ; Anti-vandal pack, anti - vandal support post - Electromechanical locking in the support post.
Delivers a signal through a 3A / 250V dry contact when a token is put in the slot (e.g.: to open the barrier).
Barrier with licence plate reader
An all-in-one solution with a licence plate reader integrated directly into the barrier housing. This system allows for the efficient management of the access control and identification of those passing through the barrier. Applications: paid car parks, hotel/camp site entrances, company car parks, etc.... Cameras may be installed on the right or left.
Button box – 1 push-button for opening/ 1 push-button for closing Control console: composed of 2 push-buttons for opening and closing. Button box – 1 push-button for opening / 1 automatic/press switch. Control console composed of: - 1 button for opening/closing – Automatic closing, - 1 automatic switch – Holds open.
Emergency services box
Emergency services box in red cast aluminium with triangle lock 3 possible opening options: - 405 key (access to the barrier or manually opened gate). - Integrated limit switch to automatically open the barrier or gate. - Switch to automatically open the gate or barrier. Dimensions: 170 w x 140 h x 48 d.
Power supply: 12 / 24 VAC – DC. Range: - 15ml for a CDR 842 A type receiver - 60ml for a CDR 852 A type receiver Operating temperatures: - 10 °C + 55 °C Paint: High resistance. Emitter and receiver: in waterproof aluminium cases. Optical head: Mounted on a moveable self-locking pivot, adjustable horizontally through a rotation of 180° and vertically through a rotation of +/- 30° from its normal starting position. Dual control: Double relays with changeover contact in series.
Keypad: 12 metal keys - backlit with blue LED lights. Case: Stainless steel front. Weight: 700g. Dimensions: 78/73 w x 125/119 h x 54/47 d mm. Power supply: 12 to 24 V AC/DC. Average power consumption: 50 amps. Operating temperatures: - 20 °C to + 70 °C. IP: 66. Relay outputs: 2 changeover contacts (NO/NF) Relays 1 = 30V DC/5A Relays 2 = 30V DC/1A
Totaliser without pre-selection - LCD 24 x 48 - non-backlit model - Display: 8 digit LCD, 8mm height - Lithium battery power supply, - Counter input: static (4-30 VDC) or voltage (10 → 260 VAC), - Reset from unit or externally with inhibition option, - Cutting accessories 50 x 25mm.
Magnetic loop sensor
Double or single channel sensor with microprocessor. Dimensions: Height 78mm, width 41mm, depth 78mm.
Range: 350 to 3,400mm. Casing: cylindrical M30. Main body: nickel-plated brass, some parts in PBT and TPU plastic. Supply voltage: 9-30 V CC, protected against polarity reversals. No-load current consumption: = ≤80 mA. Output: 1 pnp switch output. Imax = 200 Ma.
Rectangular boom with LEDs
Additional flat positioning light with LEDs for rectangular boom. Dimensions: 110 x 44mm, 13mm tall, spaced at 90mm apart.
24V flashing light
Operating voltage: 24 DC - Polystyrene base, - Polycarbonate cover, - Long-life xenon flash tubes, - Highly reliable, xenon flash tubes last for over 3,000 hours, - Entirely inert, resistant to impacts and vibration, - Protected against changes in polarity and interference, - Base and cover sealed together to ensure better water tightness. Dimensions: 77 w x 45 h.
230V flashing light
Operating voltage: 230V - Polystyrene base, - Polycarbonate cover, - Long-life xenon flash tubes, - Highly reliable, xenon flash tubes last for over 3,000 hours, - Entirely inert, resistant to impacts and vibration, - Protected against changes in polarity and interference, - Base and cover sealed together to ensure better water tightness.
Orange light Ø140-180
FH LED light Ø180mm.
R23 light Ø 120mm. Dimensions: (H x W x D): 410 x 180 x 290mm.
R24 light Ø 200mm. Dimensions: (H x W x D): 399 x 251 x 441mm.
Red light Ø180
Red FH LED light Ø180mm.
Programming: Daily programming clock.
One-way intercom 1 door station + 1 internal phone. Audio intercom kit with 2 wires, composed of a single-button door station, an internal post and a 230VAC/12VAC power supply.
For increased protection against vandalism and forcing of the barrier. The anti-vandalism kit is designed for barriers in areas at risk of vandalism. It allows equipment to be efficiently protected against malicious acts. Customisable with a choice of custom RAL paints to perfectly integrate the kit into the barrier.
PROXIMITY Compact is an access control system for doors. All the electrical components of the system are integrated into the reader casing. Compact systems can be installed on several doors at the same site, using the same badges. Readers from the P range are supplied with a choice of black or white panels which can be added after installation is complete.
Pedestrian warning sign
Sign made from A13b-type PVC. Overall dimensions: 29cm x 33cm in height. Fixed using a plastic or stainless steel collar.
Spaces/Full sign - High luminosity LEDs, - Black grained ABS panel, - "SPACES" in green LEDs, - "FULL" text in red LEDs, - 230 VAC power supply, - HO7RNF 3 × 1mm power supply cable.
La Barrière Automatique offers different varieties of terminals and access posts that can be integrated into any kind of access control: badge readers, sensors, intercoms, lights, etc. VL/PL posts. Sensor support post. Ø 80mm / 50mm signal light support post. Galvanised steel post.
S449 Radio receiver/transmitter
Anti-vandalism support post
High-resistance anti-vandalism support post designed for sensitive environments. Allows the boom to be kept in the horizontal position and prevents it from being raised manually. Designed for the LBA 10 and LBA 86-type barriers with a 175 x 175mm boom. Available with a rubber shock absorber or an 180kg capacity electromagnet (to be specified in the order). Made from sheet steel treated with cataphoresis for increased protection, and coated with polyester power paint cured at 250 °C, RAL 9010 colour paint as standard (other RAL colours available on request).
80 x 80 x 1200 support with 250kg magnet.
- Built-in siren, - Sound level: 90 dB for any application, - Continuous / rising and falling sound, - Models with terminal blocks, protected electronic circuits, - 28mm diameter holes for attaching the siren, - Low power consumption
- Siren, - Sound level: 90 dB for any application, - Continuous / rising and falling sound, - Models with terminal blocks, protected electronic circuits, - 28mm diameter holes for attaching the siren, - Low power consumption
Adjustable 230V siren
85-105 dB – 230V siren - Very powerful piezo buzzer, - Sizes: Ø 65mm, - Select from 3 distinct sounds, - Adjustable sound level, even if the device is already installed, - Ø 30.5mm holes for installation.
Locking for the LBA86R-10R boom
Boom locking through the internal system in the housing allows the boom to be locked in position. It replaces the magnet and means that the support for the end of the boom is no longer required. The system is protected from vandalism due to being completely integrated into the barrier. The locking is controlled by the barrier's programmable PLC (no need for any additional control equipment).