LBA 63 TOLL HIGHWAYS

Rapid (0.5 sec), Unbreakable

The new highway barrier, reliable, innovative, economical, ecological

More details

Specifications:  Technical details
Housing and maintenance hatch:  2mm DKP e-coated sheet metal.
Top cover:  2mm aluminium steel with phosphate coating and RAL 9010 paint.
Paint:  Polyester powder coating cured at 250°C, housing and maintenance hatch RAL 5015, top cover RAL 9010.
Boom: 3.2m carbon boom with anti-impact foam and protective Ø 85mm sleeving.
Geared motor:  Three-phase 230V 0.25KW reversible geared motor.
Counterbalance:  Counterbalance compression spring.
Standard equipment: Barrier with reversible geared motor, counterbalance and boom support. Variable speed drive with 230V 0.25KW power supply driving the acceleration ramp-ups and deceleration ramp-downs, allowing the opening and closing speed of the barrier to be controlled. Programmable PLC for controlling inductive proximity sensors. Inductive, non-contact proximity sensors for adjusting the barrier. Automatic lifting of the boom in the event of a power failure or vehicle impact when closing. Information reports on terminal: Barrier open, barrier closed, boom unhinged etc., other messages on request.
Optional equipment:  Front unhinging to avoid impacts on other highway toll equipment (e.g.: toll booth, height bar, ...), all secured by an ABS cover. Automatic rehinging with the front unhinging to allow the barrier to automatically fall back into place in the event of an impact. The boom can be replaced in less than 1 minute without needing any tools. PLC with IP connection module for uploading information to a computer network. Aluminium housing. Integrated camera in the barrier housing. 3.5m carbon boom with anti-impact foam and protective Ø 85mm sleeving equipped with reflective bands. Aluminium boom with or without foam, up to 4.00m with reflective bands. Custom colours for the housing, maintenance hatch and top cover. Fitting on the housing for affixing an entry light with integrated flashing light. Ø 200mm Red/green entry light with 230V. Siren for forced entry. Motion detector on a magnetic loop, infra-red sensor, ultrasonic detector. PVC anchor plate + 4 Ø 16 x 250mm shanks + 8 bolts. "No pedestrians" sign. 
Compatible optional equipment Technical descriptions
Token slot Delivers a signal through a 3A / 250V dry contact when a token is put in the slot (e.g.: to open the barrier).
Barrier with licence plate reader An all-in-one solution with a licence plate reader integrated directly into the barrier housing. This system allows for the efficient management of the access control and identification of those passing through the barrier.
Applications: paid car parks, hotel/camp site entrances, company car parks, etc....
Cameras may be installed on the right or left.
Button box Button box – 1 push-button for opening/ 1 push-button for closing
Control console: composed of 2 push-buttons for opening and closing.  
Button box – 1 push-button for opening / 1 automatic/press switch.
Control console composed of:
- 1 button for opening/closing – Automatic closing,
- 1 automatic switch – Holds open.
Emergency services box Emergency services box in red cast aluminium with triangle lock
3 possible opening options:
- 405 key (access to the barrier or manually opened gate).
- Integrated limit switch to automatically open the barrier or gate.
- Switch to automatically open the gate or barrier.
Dimensions: 170 w x 140 h x 48 d.
Resin detection loop Dimensions: 745mm in diameter.
Connections: 4 coils – 2 Ø1.5mm² output wires.
Materials: Resin.
Loop feeder: 7m.
Fixing: Ø 6mm.
Infra-red sensor Power supply: 12 / 24 VAC – DC.
Range:
- 15ml for a CDR 842 A type receiver
- 60ml for a CDR 852 A type receiver
Operating temperatures: - 10 °C + 55 °C 
Paint: High resistance.
Emitter and receiver: in waterproof aluminium cases.
Optical head: Mounted on a moveable self-locking pivot, adjustable horizontally through a rotation of 180° and vertically through a rotation of +/- 30° from its normal starting position.
Dual control: Double relays with changeover contact in series.
Keypad: Keypad: 12 metal keys - backlit with blue LED lights.
Case: Stainless steel front.
Weight: 700g.
Dimensions: 78/73 w x 125/119 h x 54/47 d mm.
Power supply: 12 to 24 V AC/DC.
Average power consumption: 50 amps.
Operating temperatures: - 20 °C to + 70 °C.
IP: 66.
Relay outputs: 2 changeover contacts (NO/NF)
Relays 1 = 30V DC/5A
Relays 2 = 30V DC/1A   
Cycle counter Totaliser without pre-selection - LCD 24 x 48 - non-backlit model
- Display: 8 digit LCD, 8mm height
- Lithium battery power supply,
- Counter input: static (4-30 VDC) or voltage (10 → 260 VAC),
- Reset from unit or externally with inhibition option,
- Cutting accessories 50 x 25mm.
Magnetic loop sensor Double or single channel sensor with microprocessor.
Dimensions: Height 78mm, width 41mm, depth 78mm.
Ultrasonic sensor Range: 350 to 3,400mm.
Casing: cylindrical M30.
Main body: nickel-plated brass, some parts in PBT and TPU plastic.
Supply voltage: 9-30 V CC, protected against polarity reversals.
No-load current consumption: = ≤80 mA.
Output: 1 pnp switch output. Imax = 200 Ma.
24V flashing light Operating voltage: 24 DC
- Polystyrene base,
- Polycarbonate cover,
- Long-life xenon flash tubes,
- Highly reliable, xenon flash tubes last for over 3,000 hours,
- Entirely inert, resistant to impacts and vibration,
- Protected against changes in polarity and interference,
- Base and cover sealed together to ensure better water tightness.
Dimensions: 77 w x 45 h.
230V flashing light Operating voltage: 230V
- Polystyrene base,
- Polycarbonate cover,
- Long-life xenon flash tubes,
- Highly reliable, xenon flash tubes last for over 3,000 hours,
- Entirely inert, resistant to impacts and vibration,
- Protected against changes in polarity and interference,
- Base and cover sealed together to ensure better water tightness.
R23 light R23 light Ø 120mm.
Dimensions: (H x W x D): 410 x 180 x 290mm.
R24 light R24 light Ø 200mm.
Dimensions: (H x W x D): 399 x 251 x 441mm.
Passage indication light (red-green) High visibility red/green LED lights integrated into the top cover.
Designed for:
- Indicating to vehicles that they may pass,
- Increases visibility in poorly lit areas: car parks, residential sites, industrial sites, logistics sites, etc....,
- Suitable for indoor (e.g.: covered parking area) or outdoor (site entrance, outdoor parking) usage.
Clock Programming: Daily programming clock.
Audio intercom One-way intercom 1 door station + 1 internal phone.
Audio intercom kit with 2 wires, composed of a single-button door station, an internal post and a 230VAC/12VAC power supply.
Tropicalisation kit The tropicalisation kit includes:
- 2 ventilators with filters,
- 1 fan,
- 1 heater.
This kit is adapted for use in both hot and humid environments.
Badge reader PROXIMITY Compact is an access control system for doors.
All the electrical components of the system are integrated into the reader casing.
Compact systems can be installed on several doors at the same site, using the same badges.
Readers from the P range are supplied with a choice of black or white panels which can be added after installation is complete.
Pedestrian warning sign Sign made from A13b-type PVC.
Overall dimensions: 29cm x 33cm in height.
Fixed using a plastic or stainless steel collar.
Spaces/full sign Spaces/Full sign
- High luminosity LEDs,
- Black grained ABS panel,
- "SPACES" in green LEDs,
- "FULL" text in red LEDs,
- 230 VAC power supply,
- HO7RNF 3 × 1mm power supply cable.
Bollards La Barrière Automatique offers different varieties of terminals and access posts that can be integrated into any kind of access control: badge readers, sensors, intercoms, lights, etc.
VL/PL posts.
Sensor support post.
Ø 80mm / 50mm signal light support post.
Galvanised steel post.
Radio receiver/transmitter S449 Radio receiver/transmitter
Support 80 x 80 x 1200 support with 250kg magnet.
24V siren - Built-in siren,
- Sound level: 90 dB for any application,
- Continuous / rising and falling sound,
- Models with terminal blocks, protected electronic circuits,
- 28mm diameter holes for attaching the siren,
- Low power consumption
230V siren - Siren,
- Sound level: 90 dB for any application,
- Continuous / rising and falling sound,
- Models with terminal blocks, protected electronic circuits,
- 28mm diameter holes for attaching the siren,
- Low power consumption
Adjustable 230V siren 85-105 dB – 230V siren 
- Very powerful piezo buzzer,
- Sizes: Ø 65mm,
- Select from 3 distinct sounds,
- Adjustable sound level, even if the device is already installed,
- Ø 30.5mm holes for installation.
Bell 230V bell – 105 dB at 1 metre.
Backlit mount for a logo Aimed at efficiently improving your company's visual communication.
Dimensions: 240 x 60mm.